Early Archiving Workflow Scenario with BKPF (iXOS) : Link not cre ated

[Agarwal Sharad]

Hi,
 
I am trying to work out an early archiving scenario for object BKPF (method
create : tcode FB01) using the standard workflow TS30001128. I have done all
the required config (OAC2, OAC3, SOA0, OACA, OAWS, OAG1 and OAD5).
Using SWE3(am on ver 4.7) the linkage for IMAGE ASSIGNED has been activated.
When I execute the workitem, it open ups the image in the iXOS viewer and
starts the transcation FB01. But when I save the FI document, the workitem
remains in the inbox, and the linkage is not created. I did an event trace,
and could see that the event ASSIGNED for the object
IMAGE has been raised (which is the terminating event for the task) but an
exception is raised by the Check FM (ARCHIV_WORKFLOW_ASSIGN) with a message
that 'Event not generated (creator work item 0000000000 <> receiver work
item 0000000024023).
 
Any suggestions/solutions ?? IMAGELINK-ASSIGN has been tried...it doesnt
work either.
 
Have raised an OSS note, but they havent yet got back to me. So am just
wondering, if someone in this group has any insight into the possible cause
for this ?
 
Regards
Sharad
 
(we are on ver 4.7 and are using iXOS)
 
-----Original Message-----
From: jimmy sun [mailto:jjsun02 at yahoo.com]
Sent: 14 March 2003 15:34
To: SAP-WUG at MITVMA.MIT.EDU
Subject: Fwd: Early Archiving Workflow Scenario with BKPF (iXOS) : Link
not cre ated
 
 
Agarwal,
I think you need to take a look of IMAGELINK-->ASSIGN.
 
Hope this helps.
 
Regards,
Jimmy Sun
 
 --- Agarwal Sharad <Sharad.Agarwal at thetube.com> *:0T.'!G> $i4A:
Fri,
14 Mar 2003 13:44:32 -0000
> 1H%s*L:         Agarwal Sharad <Sharad.Agarwal at thetube.com>
> %DCD: Early Archiving Workflow Scenario with BKPF (iXOS) : Link not cre
ated
> &,%s*L:           SAP-WUG at MITVMA.MIT.EDU
>
> Hi,
>
> I am trying to work out an early archiving scenario for object BKPF
(method
> create : tcode FB01) using the standard workflow TS30001128.
> I have done all the required config (OAC2, OAC3, SOA0, OACA, OAWS, OAG1
and
> OAD5).
> Using SWE3(am on ver 4.7) the linkage for IMAGE ASSIGNED has been
activated.
> When I execute the workitem, it open ups the image in the iXOS viewer and
> starts the transcation FB01. But when I save the FI document, the workitem
> remains in the inbox, and the linkage is not created.
> I did an event trace, and could see that the event ASSIGNED for the object
> IMAGE has been raised (which is the terminating event for the task) but an
> exception is raised by the Check FM (ARCHIV_WORKFLOW_ASSIGN) with a
message
> that 'Event not generated (creator work item 0000000000 <> receiver work
> item 0000000024023).
>
> Any suggestions/solutions ??
>
> Regards
> Sharad
>
 
 
*******************************************************************
Notice from London Underground Limited and its subsidiaries ("LUL")
 
This e-mail is confidential to the person to whom it is addressed.
Anyone else, please notify the sender and delete immediately,
do not disclose, use, store or copy the contents in any way.
Views expressed in this message are the individual sender's except
where specifically stated to be the views of LUL.
No contracts may be concluded on behalf of LUL by means of e-mail.
 
Copyright in this e-mail and attachments belongs to LUL.
When communicating with anyone within LUL by e-mail you consent
to the monitoring and recording of that correspondence by LUL.
 
London Underground Limited
Registered Office: 55 Broadway, London SW1H 0BD
Registered in England and Wales no. 1900907
A subsidiary of London Regional Transport
 
*******************************************************************